Ford Taurus Owners Manual [Ford] on *FREE* shipping on qualifying offers. Factory issued glove box manual. Information within each. View and Download Ford Taurus owner’s manual online. Taurus Automobile pdf on oil usage. Taurus (tau) Owners Guide (postfmt) USA (fus). Ford Taurus Owners Manual; ( Pages). (Free). Ford Taurus Owners Manual; ( Pages). (Free). Ford Taurus Owners Manual; ( Pages).
|Published (Last):||25 December 2010|
|PDF File Size:||6.59 Mb|
|ePub File Size:||8.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
Ford may change the contents without notice and without incurring obligation. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following website: Do not add friction modifier compounds or special break-in oils during the first forv thousand miles kilometers of operation, since these additives may prevent piston ring seating.
See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle.
Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter. Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Illuminates when the battery is not charging properly. Headlamps on warning chime: Stop the vehicle as soon as safely possible, switch off the engine and tayrus the engine cool.
Never remove the coolant reservoir cap kanual the engine is running or hot. Press to rewind the tape or reverse the CD. To set a station: Press to eject a tape. Do not pull too hard on the disc holder as the disc holder may come completely out of the magazine.
Mnaual this happens, reinsert the disc holder back into the magazine while pressing on the lever. When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper adhesive labels should not be inserted into the CD player.
Controls the volume of air circulated in the vehicle. For more information, refer to Rear window defroster later in this chapter. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument foed. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
Recirculation may turn off automatically in all airflow selections. Press to increase or decrease the temperature in the cabin.
Distributes air through the instrument panel registers. The set point temperatures in Celsius will be displayed in one degree increments. For more information, or to replace the filter, see your Ford or Lincoln Mercury dealer. The Daytime Running Lamp DRL system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted.
Press the controls on either side of each lens on each map lamp to activate the lamps. Remove the bolt 1 from the headlamp housing. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. Remove the bulb retaining ring by rotating it counterclockwise. Remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly. Turn the headlamps on and make sure they work properly.
If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Remove two screws and the lower trim panel from the liftgate. Remove the upper trim panel. Remove the rubber ownee from the lower access hole in the upper portion of the oqner.
Ford Taurus Owners Manual | eBay
Remove the two outboard grommets from the inside of the ownner. On the inside of the decklid, remove the three nuts that hold the spoiler on and remove the spoiler. Carefully twist and pull the socket from the lamp housing. Carefully pull the bulb from the socket and push in the new bulb. Reinstall the socket in the lamp housing and twist to secure.
Carefully push the carpet back in to place and install the plastic cover inside the trunk with five push pins and two plastic mushroom nuts. Pull the bulb straight out of the socket and push in the new bulb. Install bulb socket in lamp assembly by turning clockwise.
Carefully install the tail lamp assembly on the body side panel and secure it with two bolts. Rear window wiper and washer wagon only The rear wiper control is located under the headlamp controls.
Press the wiper control to activate the rear wiper. Press again to turn off the wiper. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers.
The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Press completely down on AUTO and release quickly. Press again to stop. R Reverse to ensure a bright clear view when backing up. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. Press the ON control and release 2. Accelerate to the desired speed.
Press the RES resume control and release it. This will automatically return the vehicle to the previously set speed. Each tap will decrease the set speed by 1 mph 1. Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency onwer.
The name and color of the button may vary by manufacturer. The indicator light will flash slowly and then rapidly after HomeLink accepts the radio frequency signal. The indicator light will begin to flash after 20 seconds. For questions or comments, contact HomeLink at www. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. Upon refueling, your vehicle must determine the percentage of Ethanol in the fuel.
If the compass still appears to be inaccurate, a manual calibration may be necessary. Determine your magnetic zone by referring to the zone map. Setup menu Press this control for the following displays: Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap gord proper installation. Hard objects can injure you in a collision. To remove the floor mat, reverse the installation procedure.
This net is not designed to restrain objects during a collision. Cargo cover if equipped Wagon Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your vehicle. Fold the edges of the 22002 towards the center, making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to the left side of the tube. Loosen the thumbwheel at both ends of the cross-bar. Slide the cross-bar to the desired location.
Tighten the thumbwheel at manuall ends of the cross-bar. Use adjustable tie down loops to secure the load. You must complete Steps within 30 seconds taurud the procedure will have to be ,anual.