MC Three-terminal Positive Voltage Regulator These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide. MC Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components. Motorola Semiconductor MC datasheet, (MC Series) Three Terminal Positive Fixed Voltage Regulators (1-page), MC datasheet, MC pdf.
|Published (Last):||25 December 2011|
|PDF File Size:||6.19 Mb|
|ePub File Size:||17.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Email Required, but never shown. Output Transistor Safe-Area Compensation? Machine Model Method V. How much higher depends on the type of regulator. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
An LDO might have a dropout voltage of 0. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. From what i understand then from your answer If you have an input voltage of 20V the same 1A will be drawn from that 20V. Output Current in Excess of 1. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. So if you have a 12W load it will draw 1A from the regulator.
I’ve seen LDOs with datashee dropout voltage of 50 mV. A control element will vary the resistance in practice a transistor so that the output voltage will remain constant regardless of input voltage and load. NCV prefix is for automotive and other applications requiring site and change control.
So you won’t find a parameter “minimum input voltage”, but it is mentioned as a condition for proper operation within certain limits.
Linear regulators are different.
The minimum voltage obtainable with this arrangement is 2. Internal Thermal Overload Protection? Maximum Power Dissipation – The maximum total device dissipation for which the regulator will operate within specifications. Datsheet difference of 8W will be dissipated in the regulator.
MC Datasheet(PDF) – Fairchild Semiconductor
The circuit of Figure 10 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor.
SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Stresses exceeding Maximum Ratings may damage the device.
So the 20V delivers 20W, while the load only consumes 12W. A note on dissipation: On page 6 of the datasheet, the datassheet dropout voltage Vd is listed as 2. In many low current applications, compensation capacitors are not required. The input voltage must remain typically 2. Since the output is 12 volts, you add the two together to get a minimum input dxtasheet The input voltage must be above the output.
Resistor R determines the current as follows: XX, These two digits of the type number indicate nominal voltage. Therefore it’s best to keep the input voltage just above the minimum to prevent the regulator to become overheated.
How does it go from a Maximum dropout voltage to a minimum input voltage? Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Functional operation above the Recommended Operating Conditions is not implied. If we look further we can see two values for line regulation; it appears that this is best if the input voltage is at least 16V.
Even though the typical dropout voltage is 2 volts, you should use the maximum value in your design. The is a non-LDO linear regulator, which means it needs a higher input voltage. There are LDOs Low Drop-Out which still can regulate the output if the input is only a few hundreds of mV higher and there are even ultra low drop-out types which only need a few tens of mV.
This literature is subject to all applicable copyright laws and is not for resale in any manner. This is a snapshot of page Sign up using Email and Password. An input bypass capacitor should be selected to provide good high-frequency dataaheet to insure stable operation under all load conditions.
No External Components Required? But since there’s this voltage drop the input voltage has to be higher than the output voltage.