Dimensions w x h x l: 0 x 0 x 0 mm. Weight net: kg. Power supply: VAC. Display digits: 3. Sensor input thermostat: NTC/PTC. Sensor input defrost: NTC/. Find great deals for Dixell Xw40l Wg5qbnc Universal Digital Controller Cooling & Heating NTC. Shop with confidence on eBay!. producer DIXELL type XW40L-5N0C1 mounting measures x30 mm supply V voltage type AC sensor type NTC 10kOhm/PTC measuring range up to .
|Published (Last):||7 February 2012|
|PDF File Size:||2.88 Mb|
|ePub File Size:||18.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
DIXELL WING XW40L INSTALLING AND OPERATING INSRUCTIONS Pdf Download.
Fit the probe where it is not xa40l by the End User. The instrument must not be opened. To lock and unlock the keyboard.
Page of 4 Go. This manual is part of the product and should be kept near the instrument for easy and quick. The instrument shall not be used for purposes different from those described hereunder. Check the supply voltage is correct before connecting the instrument. Do not expose to water or moisture: In case of failure or faulty operation send the instrument back to the distributor or to “Dixell S. Consider the maximum current which can be applied to each relay see Technical Data.
Ensure that the wires for probes, loads and the power supply are separated and far enough from. In case of applications in industrial environments, the use of mains filters our mod. There are 1 digital inputs free contact. An output allows the user to programme the parameter list with the “Hot Key”. The regulation is performed according to the temperature measured by the thermostat probe with a.
In case of fault in the thermostat probe the start and stop of the compressor are timed through. When defrost is not in progress, it can be activated the keypad by holding the o key pressed for about. The compressor operates in continuous mode for the time set through the “CCt” parameter. The cycle can be terminated before the end of the set time using the same activation key, o for about.
Two defrost modes are available through the “tdF” parameter: The defrost interval is control by means of parameter “EdF”: At the end of defrost the drip time is controlled through the “Fdt” parameter. To display and modify target set point; in programming mode it selects a parameter or.
By holding it pressed for 3s xe40l max or min temperature is displayed it will be erased. To see the max. By holding it pressed for 3s the fast x4w0l cycle.
To see the min stored temperature; in programming mode it browses the parameter codes. By holding it pressed for 3s the defrost is started.
Each LED function is described in the following table.
The “Lo” message will be displayed followed by the minimum temperature recorded. By dkxell the n key or waiting for 5s the normal display will be restored.
The “Hi” message will be displayed followed by the maximum temperature recorded. By pressing the o key or waiting for 5s the normal display will be restored.
To reset the stored temperature, when max or min temperature is displayed:. Push and immediately release the SET key: To change the Set value push the o or n arrows within 10s. To memorise the new set point value push the SET key again or wait 10s. Push the DEF key for more than 2 seconds and a manual defrost will start. To enter the parameter list “Pr1” user accessible parameters operate as follows:.
The instrument will show the first parameter present in “Pr1”. Add to my manuals Add. Digital controller with off cycle defrost and aux relay 4 pages.
Digital controller with defrost and fan management 5 pages. Page 2 dtE Defrost termination temperature: This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.
Dixell Xw40l Wg5qbnc500 Universal Digital Controller Cooling & Heating NTC
To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print.
Don’t have an account?