FARGO DTC515 MANUAL PDF

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Gugar Kejin
Country: Great Britain
Language: English (Spanish)
Genre: Life
Published (Last): 9 August 2007
Pages: 327
PDF File Size: 4.84 Mb
ePub File Size: 6.55 Mb
ISBN: 411-6-72440-905-3
Downloads: 41025
Price: Free* [*Free Regsitration Required]
Uploader: Akisida

Insert the Cleaning Cartridge back into the Printer. Disconnect the cable connector. Print a test card as described in Step 1. Press the Select button to save the value. Page of Go. To print the manual completely, please, download it. If the head cycles but does not stop at the position every time, check the Headlift Sensor as described in Sensor Testing on page Measure the total size of the desired area, and enter those dimensions into the Dimension boxes. An overlay or an overlaminate must protect Dye-Sublimation printing or it will quickly begin to wear or fade.

The Default settings for the Lamination Dwell Time and Temperature are preset for factory-recommended card stocks and overlaminate types.

FARGO ELECTRONICS DTC SERIES TROUBLESHOOTING MANUAL Pdf Download.

Printing A Test Image Note: Extra Card Cleaning Cartridge fully assembled with tape for easy loading. Rotate the Printhead Assembly out from the retaining hooks on the sides of the Printhead Arm Assembly.

Use this card to confirm that image colors are properly reproduced. Using the Encoding Mode option Use the Encoding Mode option to specify which magnetic encoding standard to use. Page 82 Page 83 – Resolving the incomplete Resin Printing Move the slide slightly toward a lower gargo if the Printer seems to double-feed cards.

  CATALOGO BUJIAS CHAMPION 2012 PDF

Select Hopper 2 to print only from Hopper 2 in this same fashion. Got it, continue to print. This square represents the first defined area. Replacing the Printhead Assembly continued Compress these 2 springs to remove the Printhead, as shown below. However, the outline around the illustration will always remain in the same landscape orientation.

Fargo DTC500 Specifications

Select this option in conjunction with any application program that supports a multiple-page document, duplex printing. Confirm that the cooling fan above the Printhead is operating properly. To illustrate this, the card illustration shown in the Image Position box will flip and rotate according to whether you have selected the Portrait or Landscape radio buttons.

Clicking on the About button Click this About button to open a dialog containing the copyright and version information about this Printer driver software. Repair the Ribbon by taping it back on to the take-up core if the Ribbon is broken. Resolving The Dram Memory Error These options allow you to control the Printer’s lamination process.

The take-up end is the other side. This option is set according to the card size for which your Encoder is physically positioned inside the Printer.

When this occurs, press the Cancel soft key to manually eject the mistakenly verified card. To do this, pull out on the Securing Tab located on the bottom of the Printer, and slide the Card Output Hopper completely out of the Printer.

Page – Calibrating the Card Lamination Module’s Be extremely careful not to let any alcohol drip inside the Printer! Step Procedure Select the Magnetic Encoding tab to display options for controlling the Magnetic Stripe encoding process.

FARGO Electronics DTC500 Series Troubleshooting Manual

Locate the Sensor near the bottom of the Printer. Firmware Errors Switch Box or peripheral. Encoding Errors Determine if the Main Board is bad.

  LIGHTPATH RESTORATION IN WDM OPTICAL NETWORKS PDF

Set the Printer on the lamination module’s Baseplate at an angle as shown. Be sure to have high Coercivity cards installed when running this test. This option is helpful if, to omit the overlay or printing around a card’s smart chip or Magnetic Stripe. Remove the Top Cover.

Locate the Printhead Setting Number on the bottom of the Printhead. Don’t show me this message again. Replacing The Main Board d 3 Circuit Board mounting screws located at the left, middle and right sections. Press the button below Select to choose an option. Set the Printer upright carefully. Enter text from picture: This is the fastest way to apply the film lamination, yet it provides the lowest film durability. Tip the Printer carefully on its back and remove the Headlift Motor through the bottom access hole.

If the PolyGuard patch is being placed more toward a card’s top edge as shownmove the Card Guide Rail slightly toward the rear of the Printer opposite the direction you would like the patch to move.

Resolving the incomplete Resin Printing problems continued See the previous procedure in this drc515. Adjusting The Ribbon Tension Trailing edge. Farho The Main Board d Note: Click on the Send Update button to bring up the Sending Update to Printer dialog, as shown on the next page. Remove the two 2 Circuit Board mounting screws located in the Hopper opening.