M68 CCO TM PDF

ARMY TM &P* AIR FORCE TO 11W TECHNICAL M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT M68 Cco Tm Manual Army – p s – scribd TM. CHAPTER I. PRESENTATION. Aimpoint CompM4 Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement. M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT CLOSE COMBAT OPTIC (CCO) (NSN ) (NSN ).

Author: Zololmaran Morr
Country: New Zealand
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 21 February 2010
Pages: 411
PDF File Size: 8.65 Mb
ePub File Size: 1.50 Mb
ISBN: 811-5-77540-899-2
Downloads: 89704
Price: Free* [*Free Regsitration Required]
Uploader: Kajas

There are two configurations of the M Also included are explanations of safety and hazardous materials icons used within this technical manual. Failure to observe these precautions could result coc serious injury or death to personnel. To maintain or regulate, within prescribed limits, by bringing into proper position, or by setting the operating characteristics to specified parameters. Right here, if this is the first time you are fco this TM. Red dot does not appear.

Army Publishing Directorate

The scribe mark is ccp by drawing a line on ring 3 of sight assembly, straight across from where the curved and flat surfaces on top join near bolts 4. Sight has a circular sized adjustment area with a diameter of 6 ft at yds 2.

The manufacturer’s part number. Insert spare battery vco into the double battery holder 3. Warning Summary 2 pages Install front and rear lens covers 1 over torque knob 2. For night vision operations, close front lens cover before turning switch knob clockwise to positions 1 thru 7.

  BESELER 67C MANUAL PDF

Refer to TM The work time figure represents the average time required to restore an item assembly, subassembly, component, module, end item, or system to a serviceable condition under typical field operating conditions.

Sending units, brackets, filters, and bolts are listed with the component they mount on. NOTE Sight is equipped with 16 positions for different dot intensity settings.

The M68 Close Combat Optic

When mounting on the M16A2 rifle, the special shaped spacer is removed. Items are returned to the user after maintenance is performed at this level.

To adjust specified variable elements of an item to bring about optimum or desired performance. These work packages also include parts which must be removed for replacement of the authorized parts. For Tactics, Techniques and Procedures Thursday, we are continuing our discussion on optics.

They are part of a kit which is authorized to the maintenance level indicated in the third position of the SMR code. Then close rear lens cover 5.

The front and rear lens covers should always be kept closed when the sight is not in use. Government agencies and their contractors.

It should mount flush on both sides of the sight. To ensure that sight assembly 1 is secure, tighten torque knob 3 until it snaps two times. The fax number is DSN or Commercial This column gives the designated interval when each check ccl to be performed.

  BOURNVITA BOOK OF KNOWLEDGE PDF

Since the M68 must be removed when the weapon is stored, note the serial number and the rail slot to enable return of same sight to the same rail slot on the same weapon to retain zero.

The code recorded in column 6 of the MAC.

The M68 Close Combat Optic |

The Comp M4 adjustment caps have straps and battery cap has an O-ring that keep out moisture. Remove large particles from exposed lens surfaces by first blowing on the surfaces.

Identifies the stock number of the item to be used for requisitioning purposes. If the third position of the SMR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher level, order the item xco the higher level of maintenance.

This item is also identified by the NSN listed on the same line. Order the next higher assembly.

TM 9-1240-413-13&P S60288

The lowest level of maintenance authorized to use the tool or test equipment. Cc front cover 3adjust intensity with target background. Keep gap between plate spacer 1 and base assembly 6 equal on both sides.